2012 CATERPILLAR D11T


Details

  • 135085CFS
  • JEL00222
  • EROPS; OROPS; AIR CONDITIONER; RIPPER, SINGLE SH; STEER, FINGER TIP CONTROL; HYD CONTROL; ENGINE ENCLOSURES; PRODUCT LINK; LIGHTING; ULTRA LOW SULFUR DIESEL FUEL; PRODUCT LINK; AM FM CD RADIO; NO BLADE INCLUDED WITH THE MACHINE. A BLADE IS AVAILABLE TO PURCHASE AT AN ADDITIONAL COST.; ; OVERALL RATING: As-Is, Model: D11T

  • Click here for more information
  • 26,507
  • $541,500.00 USD
  • EDMONTON, AB CAN

Contact Us

Phone Email
Refresh Captcha




By clicking Submit, I agree to Caterpillar Financial's
Privacy Policy and Terms of Use.

Tools

Payment Calculator Finance Application Lease / Own Comparison


New     Very Good     Good     Fair     Poor

GENERAL APPEARANCE

Cleaning RequiredLEAKING STAIR PUMP SPRAYED HYD FLUID ALL OVER MACHINE. CAB ALSO NEEDS CLEANING.
S.O.S. Taken

NotesMISSING RH LIFT CYLINDER REAR VIEW MIRROR.
Cab or Canopy
DecalsSOME SCRATCHES AND RIPS IN DECALS
Fenders
Fuel Tank
Grab IronsRH SIDE CRACKED
Hood
Main Frame Welds
PaintSCRATCHES AND SURFACE RUST ON HIGH WEAR AREAS. HAS UNIT NUMBERS. MACHINE SHOWS FAIR FOR AGE AND HOURS.
Pre-Cleaner Bowl
Sheet MetalPIVOT SHAFT OIL DOOR LATCH SEIZED. DOOR UNDER CAB FILTER LATCH SEIZED AND HINGE BROKEN.
Steps / LadderHYD STEP MOTOR LEAKING BADLY DURING OPERATION

SAFETY ITEMS

ROPSYes
Back Up Alarm
Horn

NotesSECONDARY EXIT - GOOD

GAUGES, OPERATOR STATION, CONSOLE

Air ConditionerNOT WORKING VENT TEMPS 86F
Dash ConsoleCOUPLE SMALL CRACKS IN PLASTIC. RH LOWER VENT BROKEN.
EMS Panel / Warnings
Gauges
Glass/MirrorsLH WINDOW DOESN'T OPEN. REAR GLASS CRACKED.
Heater
Interior LightsAMBER ROOF LIGHTS WON'T SHUT OFF.
Seat Cushion / Arm RestLH CONSOLE UP/DOWN ADJUSTMENT MOTOR NOT WORKING. LOWER SEAT CUSHION MOUNTING HARDWARE MISSING. SOME SMALL RIPS IN SEAT CUSHION.
SwitchesPARKING BRAKE SWITCH NOT LEGIBLE
Windshield WipersREAR NOT WORKING. DOOR SPRAYERS NOT WORKING. NEEDS NEW WIPER BLADES.
Current O&MM
Current Parts Manual
Current Safety Manual
ROPS Certification Plate

ENGINE

Air Cleaners10" of h2o restriction
Engine Supports
Fuel Injection Systempassed cylinder cutout tests
Operating Conditionengine starts and runs well
Turbocharger / Blower28 psi boost under load. rh turbo intake tube missing clamp
Blow ByNORMAL AMOUNTS OF BLOW BY
Compression in Radiator
Fluid Levels OK?TRANSMISSION OIL LOW
Knocking
Oil LeaksFRONT AND REAR OF OIL PAN LEAKING. BOTH STARTER GASKETS LEAKING.
Water in Oil
Oil Pressure (H/L/N)22 PSI LOW IDLE 60 PSI HIGH IDLE

COOLING SYSTEM

Leaks
Standard Radiator
Belts / Pulleys
Coolers
Fan
Hoses
Radiator
Water Pump

Notesengine temperatures stayed constant and within range during testing. levels were good.

ELECTRICAL, STARTING AND CHARGING SYSTEM

Block Heater
Ether Aid
AlternatorCharging at 27.5 V
Batteries / CablesCat 1400 CCA X 4 all tested good. Dirty and terminals need service
Starter
Wiring

TRANSMISSION

Leaks
Transmission - Noisy

NotesUniversal Joints - Good
Case
Controls
Cooler
Lines / Fittings
Operating ConditionTransmission shifted well through all gears forward and reverse. Stalls at same speed in all gears.
Pump
Seals
Temp / Pressure Gauges
Transmission - Forward Shifts
Transmission - Reverse Shifts

STEERING

Steering Clutch

NotesSteering stem worked well with no issues noted during testing.

BRAKE


NotesType (Pedal. Lever) - Good Pedal. Type (wet. Dry) - Good - Wet. Pump - Good. Control Valve - Good. Lines - Good. Operating Condition - Good
Holding What Gear?2nd

HYDRAULICS

Lift CylindersRh cylinder leaking. LH cylinder slightly weeping.
Overall Operating ConditionBlade not on machine so couldn't test lift or tilt cylinders. Ripper system worked without any issues. No issues noted with pumps valves etc with the limited testing.
Ripper Lift Cylinder
Ripper Tilt Cylinder

NotesBlade tilt port block off plate leaking. Leak at LH side by torque. Very wet couldn't pinpoint needs wash.

BLADE

Push Arm
Tilt Arms

NotesDraglink - Good. Blade not with mchine push arms etc were on pallets. Looked to be in good shape.

RIPPER / GRAPPLE / WINCH

Beam / Frame
Brackets / Studs
Pins & Bushings
Shanks / GETApprox 50% remaining
Hydraulic Winch
Mechanical Winch

UNDERCARRIAGE


NotesTracks were very loose and were skipping on sprockets during operation. SSSSDDSS

Equalizer BarLH side leaking

Pivot ShaftOil was low. No signs of external leaks.
Track Frame - Left
Track Frame - Right

Average Life Remaining0%


Measure (L) Measure (R) % Worn (L) % Worn (R) Potential Hrs (L) Potential Hrs (R)
Idlers Front1.42"1.38"10096
Idlers Rear1.52"1.5"110108
Links1.631.949657
Pins & Bushings (External).50".60"8464
Segments313mm321mm10991
Track Roller 1.74".88"120120
Track Roller 20.99"1.02"120117
Track Roller 32.40".18"34120
Track Roller 42.43"1.0132119
Track Roller 51.151.07"120125
Track Roller 61.15".52120130
Track Roller 71.111.31"115107
Track Roller 82.33".84"40120
Pins & Bushings Turned?No

FINAL DRIVES

Housings, Left
Housings, Right
Planetaries / Differential, Le
Planetaries / Differential, Ri

NotesRH oil level slightly low and LH slightly high. Oil was clean and no excessive wear metal found on mag plugs.